Colorful Wax Resin Ribbon

Thermal Transfer Ribbon with heat transferable coatings.

Thermal Transfer Ribbon with heat transferable coatings.

CAS No.

25308-59-9

13463-67-7

8002-74-2

65997-11-7

Chemical Components

Polyethylene terephthalate/PET

Titanium dioxide Paraffin wax

Resin & etc

%(Optional) 45-55

18-25%

16-21% 8-13%

CAS No.

Polyethylene terephthalate/PET

45-55

25308-59-9

Titanium dioxide Paraffin wax

18-25%

13463-67-7

Paraffin wax

16-21%

8002-74-2

Resin & etc

8-13%

65997-11-7

Section 3 Hazardous information

Risks for human health:

This product is relatively innocuous substance and is eyes, nose and throat may occur  if slitting. Suggest generated during slitting, etc

Environmental risks:  No data available

not expected to cause harm. Mechanical irritation of the 10mg/Cu .M for inert or nuisance particulate if debris is

Section 4 First aid measures

Route of Entry: Inhalation Skin  Ingestion (Possible but very unusual)

Ingestion: If swallowed, get medical attention.

Skin : If irritations are felt after contact with skin, wash with plenty of mild soap and water.

Eyes : In case of contact with eyes, rinse immediately with plenty of water for at least 15 minutes and seek

medical advice.

Signs and Symptoms of Exposure : None

Medical Conditions(Generally aggravated by Exposure) : None

Section 5 Fire-fighting measures

Section 6 Accidental release measures

Not applicable

Section 7 Handling and storage

Handling: Wash through after handling and before eating or smoking. Eye protection is recommended if ribbon is being slit or cut. Use adequate ventilation nuisance particles are being generated.

Storage: Should be stored in dark and cool place. sheltered from Direct light. Short term storage(24H) :Temperature -20～ 55℃ , Humidity 10～ 85% RH.Long term storage( 1 Year) : Temperature 0 ～40℃ , Humidity 30 ～ 90% RH. Avoid proximity of flame and heat sources. Store 24 hours in room temperature before slitting.

Section 8 Exposure controls/ personal protection

Technical protection measures: This product will slowly photo degrade with UV light exposure, shelter from light.

Personal protection equipment: Goggle for eye protection and particle mask for nose and throat protection during slitting process.

Section 9 Physical and chemical

properties

Appearance: Ink coated film

Color: White

Odor: little or no odor

Change in physical: Not applicable

Melting point: Ink,83℃/Film ,258℃

Boling point: Not applicable

Flash point: ＞160℃

Ignition temperature: Not applicable

Danger of explosion: Not applicable

Explosion limit: Not applicable

Vapor pressure( Air= 1 ) : Not applicable

Solubility: Not applicable

PH-value: Not applicable

Specific gravity(H2O= 1) : About 1.37-1 .38

Section 10 Stability and reactivity

Stability: Stable

Hazardous decomposition products: Terephthalic acid, CO and aldehyde above 300℃

Byproducts: CO, CO2 , NOX and H2O etc.

Section 11 Toxicological information

Health effects : None  known Acute toxicity:     Not found

Others information:

The TTR will contain  levels  below those listed below(the  European Union”s RoHS Legislation Directive 2002/95/ EC).

Section 12

Ecological information

Aquatic toxicity:

Not available Biodegradability: Not available

Effect on effluent treatment: Biodegradability

Section 13

Disposal consideration

Disposal definition: Scrap film from slitting, ribbon after printing barcode.

Waste disposal: Disposal in accordance with local state and federal regulations.

Section 14 Transport information

No special

Section 15 Regulatory information

No special

Section 16 Other information

No liability is accepted for any injury, loss damage or cost arising directly or indirectly from the

use of any information contained within this MSDS since the customer”s treatment of the product is necessarily out of our control.